Renault Megane

Only for vehicles not equipped with the A switch of the "My Safety" function, the system "Advanced safety" is made up of:

  • active emergency braking;

and

  • emergency lane departure prevention.

The "Advanced safety" system uses information from the camera 1, front radar 2 and, depending on the vehicle, side radars 3.

warning

This system provides an additional driving aid.

This system is not, under any circumstances, intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

Location of the camera 1

Make sure the windscreen is not obscured (by dirt, mud, snow, condensation etc.).

Location of the front radar 2

Ensure that the radar area is not obstructed (dirt, mud, snow, a badly fitted/attached front number plate), impacted, modified (including paintwork) or hidden by any accessory fitted on the front of the vehicle (on the front bumper, logo, etc.)

Location of the side radars 3

Ensure that the radar area is not obstructed (by dirt, mud, snow etc.), impacted or modified (including paintwork etc.).

tip

Depending on the sensitivity setting selected, the "Lane departure prevention" function may operate prior to operation of the "Emergency lane departure prevention" system.

Activating, deactivating the system from the multimedia screen 4

From the "Vehicle " World on your multimedia screen 4, press the "Driving assistance" menu, then the "Advanced safety" menu to access the activation/deactivation of the function.

The 2_ALL_401_1_pictogramme.png warning light appears in yellow on the instrument panel when the system is deactivated.

When the system is activated, the warning light disappears.

tip

This system is reactivated each time the ignition is switched on.

Active emergency braking

The system uses information from the radar 2 and the camera 1, to determine the distance between your vehicle:

  • from the vehicle ahead in the same lane;

or

  • from any oncoming vehicles in the context of a manoeuvre to change direction;

or

  • surrounding pedestrians and cyclists.

The system informs the driver if there is a risk of head-on collision to enable appropriate emergency manoeuvres (pressing the brake pedal and/or turning the steering wheel).

Depending on the reactivity of the driver, the system can assist with braking in order to limit damage or prevent a collision.

warning

This function is an additional driving aid.

This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

tip

This system can apply maximum braking to the vehicle until it is completely stationary if necessary.

For safety reasons, always wear your seat belt when travelling in your vehicle and make sure that it is loaded so that no items can be thrown forward and hit the occupants.

Detection of vehicles

When driving, from approximately 5 mph (8 km/h), if there is a risk of collision with the vehicle in front or with a vehicle moving in the opposite direction when changing direction or with a stationary vehicle or a vehicle passing perpendicularly, the system will warn you of a risk of collision or may trigger braking.

Collision risk alert

The warning light 2_ALL_442_1_pictogramme.png or, depending on the vehicle, the display 5 and the "Brake" message appears on the instrument panel, accompanied by a beep and a haptic warning (micro braking according to the sensitivity level and speed).

If the driver presses the brake pedal and the system still detects a risk of collision, the braking force may be increased if it is not sufficient to prevent the collision.

Triggering of braking

If the driver fails to react following the alert and collision becomes imminent.

If active emergency braking has caused the vehicle to stop, the vehicle is kept stationary for a short time.

Beyond this time limit, the vehicle must be held stationary by the driver keeping their foot on the brake pedal.

Note: if the driver uses the vehicle controls (steering wheel, pedals, etc.) the system may delay certain operations or not activate.

tip

In the event of an emergency manoeuvre, you can stop the braking at any moment by:

  • tapping the accelerator pedal;

or

  • turning the steering wheel as a collision avoidance manoeuvre.

Special features of oncoming vehicles in the context of a manoeuvre to change direction

When you wish to change direction (e.g. A)), oncoming vehicles travelling at approximately 18 mph (30 km/h) to 35 mph (55 km/h) are detected by the system when:

  • your vehicle is travelling at a speed between approximately 5 mph (8 km/h) to 12 mph (20 km/h);
  • you have activated the direction indicator light.

The system is otherwise inactive and does not trigger an alert.

warning

This function is an additional driving aid.

This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

Special features of stationary vehicles

Stationary vehicles are detected when your vehicle is being driven at a speed between approximately 5 mph (8 km/h) and 50 mph (80 km/h).

The system is not active and does not emit a warning for stationary vehicles when you exceed approximately 50 mph (80 km/h).

Special features of warnings

Depending on the speed, the warning and braking may be activated simultaneously.

Detection of pedestrians and cyclists

When driving at a speed between approximately 5 mph (8 km/h) and 53 mph (85 km/h), if there is a risk of collision with a cyclist or pedestrian, the system:

  • warns you of a collision risk:

warning light 2_ALL_442_1_pictogramme.png or, depending on the vehicle, the 5 is displayed and the "Brake" message appears on the instrument panel, accompanied by a beep.

If the driver presses the brake pedal and the system still detects a risk of collision, the braking force may be increased if it is not sufficient to prevent the collision;

  • may trigger braking:

if the driver fails to react following the alert and collision becomes imminent.

If active emergency braking has caused the vehicle to stop, the vehicle is kept stationary for a short time.

Beyond this time limit, the vehicle must be held stationary by the driver keeping their foot on the brake pedal.

Note: if the driver uses the vehicle controls (steering wheel, pedals, etc.) the system may delay certain operations or not activate.

tip

In the event of an emergency manoeuvre, you can stop the braking at any moment by:

  • tapping the accelerator pedal;

or

  • turning the steering wheel as a collision avoidance manoeuvre.

Settings

From the "Vehicle" World on your multimedia screen 4, press the "Driving assistance" menu, then the "Advanced safety" menu to access the following settings:

"Warning anticipation": adjust the alert sensitivity level. To do this select:

  • « Late » ;
  • « Standard » ;
  • « Early ».

Temporarily not available

When the system detects a temporary unavailability, the 2_ALL_442_1_pictogramme.png or, depending on the vehicle, 2_ALL_401_1_pictogramme.png lights up in yellow on the instrument panel.

The possible causes are:

  • the system is temporarily blinded (glare from the sun, dipped beam headlights, bad weather conditions etc.). The system will be operational again when visibility conditions are better;
  • the system is temporarily interrupted (e.g. the windscreen, front or rear bumper or logo is obscured by dirt, mud, snow, condensation, etc.) In this case, park the vehicle and switch off the engine. Clean the windscreen and front bumper. The next time the engine is started, after five or ten minutes of driving, the warning light and the message disappear.

If this is not the case, this may arise from another cause; contact an Approved Dealer.

Operating faults

When the function detects a malfunction, the warning light 2_ALL_401_1_pictogramme.png is displayed on the instrument panel along with, depending on the malfunction, one of the following messages:

  • « Check Front camera » ;

or

  • « Front radar to check » ;

or

  • « Check Driving assist ».

Consult an approved dealer.

Warnings

warning

Active emergency braking

This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steering wheel, pedals etc.).

The system cannot be activated:

  • when the gear control is in neutral position;
  • when the Electronic Stability Program (ESC) has been triggered.

System servicing/repairs

  • In the event of an impact, the radar and/or camera alignment may be changed and its operation may consequently be affected. Deactivate the function and consult an authorised dealer.
  • Any work in the area where the radar and/or camera is located (repairs, replacements, windscreen modifications, etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

warning

System disturbance

Some conditions can disturb or damage the system's operation, such as:

  • a complex environment (metal bridge, tunnel, etc.);
  • poor weather conditions (snow, rain, hail, black ice, etc.);
  • poor visibility (night, fog, etc.);
  • poor contrast between the object (vehicle, pedestrian etc.) and the surrounding area (e.g. pedestrian dressed in white located in a snowy area etc.);
  • being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);
  • windscreen obscured (by dirt, ice, snow, condensation etc.);
  • ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

Limitation of the system operation

  • Each time the vehicle is started, the system carries out a calibration according to the vehicle surroundings and may be inactive for a length of time between approximately two to five minutes of driving;
  • an oncoming vehicle will not trigger any warning or system action if the conditions detailed in the paragraph on "Special features of oncoming vehicles when changing direction" are not met;
  • the radar and camera zones must be kept clean and free of any modifications in order to ensure the proper operation of the system;
  • the system may not respond to small vehicles such as motorbikes as effectively as to other vehicles;
  • the system may not operate properly when the road surface is slippery (rain, snow, black ice, etc.);
  • to ensure correct operation, the system needs to distinguish the complete outline of the pedestrian. So the system cannot detect:
    • pedestrians in the darkness or in poor lighting conditions;
    • partially visible pedestrians;
    • pedestrians less than approximately 80 cm;
    • pedestrians carrying large objects;
    • ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

warning

Deactivating the function

You must deactivate the function if:

  • the camera area has been damaged (e.g. on the inside or outside of the windscreen);
  • the front of the vehicle has been damaged (impact, distortion, scratch on the radar, etc.);
  • the vehicle is being towed (breakdowns);
  • the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an approved dealer);
  • you are not driving on a paved road;
  • the vehicle is on a roller bench in a workshop.

In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.

Halting the function

You can halt the active braking function at any time by tapping the accelerator pedal or by turning the steering wheel in a collision avoidance manoeuvre.

Emergency lane departure prevention

Using information from the camera 1, the function triggers corrective action on the vehicle steering system when approaching the roadside (divider, barrier, pavement, embankment etc.) without the direction indicator light having been activated.

Using information from the radar 2 and the camera 1, the function triggers corrective action on the vehicle steering system in the event of a risk of collision with a vehicle coming from the opposite direction in the adjacent lane, without the direction indicator having been activated.

Depending on the vehicle, using information from the radars 3 and the camera 1, the function triggers corrective action on the vehicle steering system.

In the event of a risk of collision with a vehicle moving at the same speed or a higher speed, located in the detection area of the rear radars (emergency lane departure prevention in case of overtaking).

tip

You can retake control of the vehicle at any time by operating the steering wheel.

warning

This system provides an additional driving aid.

This system is not, under any circumstances, intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

Roadside detection

When driving at a speed between approximately 40 mph (65 km/h) and 112 mph (180 km/h), when approaching the roadside (on the ground, barrier, pavement, embankment, etc.), without the direction indicator having been activated, the system:

  • warns you of a collision risk:
6.

the display lights up on the instrument panel accompanied by the "Near to roadside" message;

and

  • triggers corrective action on the steering system.

Special feature

In the event the function operates repeatedly when approaching the roadside, if the system does not detect any hands on the steering wheel, the warning light 2_ALL_360_1_pictogramme.png appears in yellow on the instrument panel accompanied by the message "Keep control".

warning

This function is an additional driving aid.

This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

Detection of an oncoming vehicle

When driving at a speed between approximately 40 mph (65 km/h) and 68 mph (110 km/h), if there is a risk of collision with a vehicle coming from the opposite direction in an adjacent lane and within the detection zone B, without the direction indicator having been activated, the system:

  • warns you of a collision risk:

warning light 2_ALL_442_1_pictogramme.png and the display 6 lights up on the instrument panel accompanied by the message "Risk of collision" and a beep;

and

  • triggers corrective action on the steering system.
tip

You can interrupt the trajectory correction at any time by moving the steering wheel.

warning

This function is an additional driving aid.

This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

If case of overtaking

(depending on the vehicle)

While driving from approximately 5 mph (8 km/h), when approaching a line (continuous or broken) and there is a risk of collision with a vehicle located in the blind spot C moving in the same direction as your vehicle or with a vehicle that is rapidly approaching from behind in an adjacent lane that is in the detection area D, the system:

  • warns you of a collision risk:
7.

the indicator flashes, the red 2_ALL_442_1_pictogramme.png warning light and the display 6 light up on the instrument panel accompanied by the message "Lateral obstacle detected" accompanied by a beep;

and

  • triggers corrective action on the steering system.

Temporarily not available

The system will cease to be available if:

  • very fast lane departure;
  • driving continuously on a line;
  • approximately four seconds after changing lanes;
  • tight bends;
  • impaired visibility;
  • activation of the direction indicator (in the case of roadside detection and detection of a vehicle coming from the opposite direction);
  • strong acceleration;
  • emergency braking;
  • the lane width changes;
  • operation of the active emergency braking system;
  • ...

Depending on the vehicle, if one of the side radars is obscured the message "Check Side radars" will appear on the instrument panel.

When the front radar is obscured, the "Front radar no visibility" message is displayed on the instrument panel.

When the front camera is obscured, the "Front camera no visibility" message is displayed on the instrument panel.

Conditions for non-activation of the system

The system cannot be activated when:

  • reverse gear is engaged;
  • the field of vision of the camera is obstructed;
  • the front radar is obscured;
  • depending on the vehicle, the rear radars are obscured;
  • warning light 2_ALL_116_1_pictogramme.png is displayed.

If one of the side radars is obscured, the warning light 2_ALL_401_1_pictogramme.png lights up in yellow, accompanied by the "Side radars no visibility" message.

If the front radar is obscured, the warning light 2_ALL_401_1_pictogramme.png lights up in yellow, accompanied by the "Front radar no visibility" message.

If the front camera is obscured, the warning light 2_ALL_401_1_pictogramme.png lights up in yellow, accompanied by the "Front camera no visibility" message.

Clean the area where the sensors are located.

If the vehicle is fitted with a towbar that is recognised by the system, the warning light 2_ALL_401_1_pictogramme.png lights up in yellow accompanied by the "Trailer: side radars unavailable" message to inform you that the emergency lane departure prevention function is not in operation.

If the vehicle is towing a trailer or caravan, unexpected or unnecessary corrections may occur.

You can deactivate the "Advanced safety" function to avoid unexpected or unnecessary corrections.

Operating faults

When the function detects a malfunction, the warning light 2_ALL_401_1_pictogramme.png is displayed on the instrument panel along with, depending on the malfunction, one of the following messages:

  • « Check Front camera » ;

or

  • « Front radar to check » ;

or

  • « Check Driving assist » ;

or, depending on the vehicle,

  • « Check Side radars ».

Consult an approved dealer.

Warnings

warning

This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

  • In the event of an impact, the alignment of the camera or radar(s) may be altered and its operation may consequently be affected. Deactivate the function and consult an authorised dealer.
  • Any work in the area where the camera or radars are located (replacements, repairs, windscreen modifications etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

  • windscreen obscured (by dirt, ice, snow, condensation etc.);
  • a complex environment (tunnel, etc.);
  • poor weather conditions (snow, rain, hail, black ice, etc.);
  • poor visibility (night, fog, etc.);
  • the road markings are irregular or difficult to distinguish (e.g. partially erased, excessive spacing, distorted road surface...);
  • being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);
  • the road is narrow, winding or undulating (tight bends, etc.);
  • closely following a vehicle travelling in the same lane.

In this case, the "Advanced Safety" function may react incorrectly or not at all.

Risk of unwanted, incorrect correction or no correction of trajectory.

Deactivating the function

You must deactivate the function if:

  • the camera area (on the windscreen side or the interior rear-view mirror side) or radar area(s) have been damaged;
  • the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an approved dealer);
  • the vehicle is being towed (breakdowns);
  • you are not driving on a paved road.