Radio Connect R & GO 3

to today

Bluetooth® connection

To activate the audio system's Bluetooth® function:

  • press or to access the "Phone" menu;
  • select "BT ON/OFF" using the on the steering column control or on the panel, then press or to confirm;
  • select "YES" using on the steering column control or on the panel, then press or to confirm.

Pairing a phone

To use your hands-free system, pair your Bluetooth® mobile phone with the vehicle. Check that the your phone's Bluetooth® function is activated and set its status to "visible".

Pairing will enable the hands-free phone system to recognise and store a phone.

You can pair up to six phones, but only one can be connected at a time.

Pairing can be performed from the audio system or from your phone.

Your audio system and phone must both be switched on.

Note: if you pair a new phone while another phone is already connected to the audio system, it will be disconnected and replaced by the new paired phone.

warning

For safety reasons, carry out these operations when the vehicle is stationary.

Pairing a Bluetooth® phone with the audio system via the audio system

This method allows you to make a Bluetooth® search from the audio system.

To pair a phone, carry out the following operations:

  • activate Bluetooth®;
  • press or to access the "Phone" menu;
  • select "Search for a phone" using on the steering column or on the front panel, then or to confirm.

The search for Bluetooth® devices in the vicinity will begin (this search may take up to approximately 60 seconds.)

Select the telephone that you wish to pair by rotating on the steering column or on the panel, then press to confirm.

From your Bluetooth® device, accept the pairing request.

When the "Connected" message is displayed on the audio system screen, the Bluetooth® device is automatically stored and connected to the vehicle.

Your device is then visible in the list of recognised phones which can also be accessed in the "Select a phone" sub-menu.

If the pairing has not been successful after 60 seconds, the "Pairing failed" message appears. Repeat these operations to carry out the desired action. Please refer to your telephone's user guide for further information.

Note: depending on your phone, it may be useful to accept the transfer of your phonebook and call history.

Pairing a Bluetooth® phone with the audio system via your phone

This method allows you to make a Bluetooth® search from your phone.

To pair your phone, carry out the following operations:

  • activate Bluetooth®;
  • press or to access the "Phone" menu;
  • select "Pair phone" using on the front panel, then or to confirm.

The "Enter the code: XXXXXX" message appears on the audio system screen and a 60 seconds countdown starts.

The audio system is then visible to other Bluetooth® devices for approximately 60 seconds.

Search for the audio system using your telephone, then select it (see your telephone user manual) or accept the pairing code with your telephone.

The "MY CAR connected" or "R&Go Multimédia" message is displayed on the audio system screen to confirm that your telephone is paired and connected with your audio system.

The "R&Go Multimédia" message is displayed on the screen only if the R&Go application connects to the audio system and if the application is installed on your smartphone.

If pairing fails, the audio system display returns to the "Phone" menu.

If the maximum limit of phones paired with the audio system is reached, you need to unpair an existing phone before pairing a new one (refer to the information on "Unpairing a phone" in this section).

warning

Your hands-free phone system is only intended to facilitate communication by reducing the risk factors, without removing them completely. Always comply with the laws of the country in which you are travelling.

Unpairing a telephone

Unpairing enables you to delete a phone from the hands-free telephone system memory:

  • press or to access the "Phone" menu;
  • select the "Delete a phone" menu using the on the steering column control or on the panel, then press or to confirm;
  • select "YES" using on the steering column control or on the panel, then press or to confirm.

A message is displayed on the audio system screen asking you to confirm your choice (as shown in the illustration).

If six phones are already stored, the system offers to delete one of the devices. By selecting "YES", you will be redirected to the "Delete a phone" menu.