Renault Kwid
Your vehicle may be fitted with this function.
This system enables reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby mode) when the vehicle is at a standstill (traffic jam, traffic lights, etc).
warning
When the engine is in standby mode, steering and braking assistance are not operational.
Standby mode activation conditions
After exceeding a certain speed since the last stop, the engine will switch to standby mode when:
- the gearbox is in neutral;
and
- the clutch pedal is released
If the
warning light flashes, this indicates that the clutch pedal is not fully released;
and
- the vehicle is travelling at less than 2 mph (4 km/h).
A warning light
remains illuminated on the instrument panel, warning you that the engine is in standby mode.
The vehicle equipment remain operational while the engine is stopped.
warning
Do not allow the vehicle to move while the engine is in standby mode (shown by the warning light
on the instrument panel).
warning
For refuelling, the engine must be switched off (and not in stand by mode for vehicles equipped with the Stop & Start function): You MUST switch off the ignition Starting, stopping the engine.
Fire hazard.
warning
Before exiting the vehicle, it is mandatory to switch off the ignition by turning the key to position « stop » St.
Coming out of engine standby mode
The vehicles engine starts to run again when:
- the gearbox is in neutral, and the clutch pedal is completely pressed down;
or
- the gearbox is in gear and the clutch pedal is fully pressed down.
Preventing activation of engine standby mode
In certain situations, when crossing a junction for instance, it is possible to keep the engine running, ready to move off quickly.
Therefore, keep the clutch pedal pressed down
tip
If the engine stalls when starting, it can be restarted by fully depressing the clutch pedal.
Conditions preventing standby mode
Certain conditions prevent the engine from going into standby mode, particularly when:
- the reverse gear is engaged;
or
- the bonnet is not locked;
or
- the outside temperature is too low or too high (less than approximately 0°C or higher than approximately 35°C);
or
- the battery is not sufficiently charged;
or
- the engine temperature is too low;
or
- ...
The
appears on the instrument panel to indicate that engine standby mode is not available.
Special feature of the automatic engine re-start
Under certain conditions, the engine can restart on its own, to guarantee your safety and comfort.
This can occur especially when:
- the outside temperature is too low or too high (less than approximately 0°C or higher than approximately 35°C);
- the battery is not sufficiently charged;
- the vehicle speed is above 3 mph (5 km/h) (downhill slope, etc.);
- the brake pedal is pressed repeatedly or there is a braking system requirement;
- in vehicles fitted with a manual gearbox, the engine may stall if the clutch pedal is released too quickly while a gear is engaged.
warning
Deactivate the Stop & Start function when performing any operation in the engine compartment.
Deactivating, activating the function
The system is activated automatically every time the vehicle is started using the key (Starting, stopping the engine).
Press the switch 1 to deactivate the function. The warning light in the switch will light up.
Pressing this again will reactivate the system. The warning light built into the switch 1 will go out.
Special cases
With the engine in standby, if the driver opens the bonnet, the ignition will switch off.
To reactivate the system Stop & Start, ensure that the bonnet is securely closed and start the engine again using the key (Starting, stopping the engine).
Operating fault
If the warning light built into the switch 1 comes on without there having been a deliberate deactivation, this may indicate a system fault.
consult an approved dealer.
warning
If the engine is in standby mode, the engine can be restarted in an emergency by pressing the clutch pedal.
tip
After filling with any amount of fuel, standby mode may be stopped while the electronic injection adapts. For more information.
tip
With the engine on standby, it is possible to start the engine again by pressing the switch 1.