Renault Kwid

Operating principle

Operating principle

The system detects the loss of pressure in a tyre by measuring the wheel speed while driving.

The 2_ALL_197_1_pictogramme.png warning light 1 appears to notify the driver if the pressure is too low because of a leak, puncture, etc.

Operating conditions

The system must be reset with a tyre pressure equal to that shown on the tyre pressure label. Otherwise there is a risk that the warning system will not be reliable when there is a significant loss of pressure Tyre pressure.

In the following situations, there is a risk that the warning system will be activated late or not work correctly:

  • if the system is not reset after the tyres are inflated or following any other operation on the wheels;
  • if the system is reset incorrectly. if the tyre pressure is different to that recommended;
  • a significant change to the load or the load distribution on one side of the vehicle;
  • sporty driving using rapid acceleration;
  • when driving on a slippery or snow-covered surface;
  • when driving with snow chains;
  • when only one new tyre is fitted;
  • if using tyres not approved by the network.
  • ...

Resetting the tyre pressure reference value

This should be performed:

  • every time a tyre is inflated or the pressure is adjusted;
  • when the normal tyre pressure is changed to adapt to specific driving conditions (vehicle empty, loaded, motorway driving, etc.);
  • after changing a wheel;
  • after using a tyre inflation kit;
  • after tyre rotation.

It should always be done after checking the tyre pressure of all four tyres when cold.

Tyre pressures must correspond to the current usage of the vehicle (empty, carrying a load, motorway driving, etc.).

Resetting procedure via instrument panel A

Ignition on, vehicle stationary:

  • Press the switch 2 as many times as necessary, until "Tyre pressure appears on the instrument panel A;
  • press and hold switch 3 "OK" and then confirm the "Reset" option.

Once the operation is complete, you can drive again.

Display

Inflate the tyres

The warning light 2_ALL_197_1_pictogramme.png will come on and remain steady.

This warns that at least one tyre is flat or punctured.

If a tyre is flat, inflate it.

In the case of a puncture, change the tyre or contact an approved dealer.

Check and adjust the pressure of the four tyres when they are cold and reset the tyre pressure reference value.

The 2_ALL_197_1_pictogramme.png warning light goes out when the tyre pressure reference value is reset.

warning

For your own safety, if the warning light 1_ALL_040_1_pictogramme.png comes on, stop immediately, or as soon as traffic conditions allow.

Reset the tyre pressure.

The warning light 2_ALL_197_1_pictogramme.png will flash for a few seconds and then remain steady.

This indicates that the request to reset the tyre pressure reference value should be made again.

System unavailable

The warning light 2_ALL_197_1_pictogramme.png will flash for a few seconds and then remain steady.

Indicates that the vehicle is fitted with a spare wheel that is smaller that the other four wheels installed on the vehicle.

System to be checked

The 2_ALL_197_1_pictogramme.png warning light flashes for a few seconds and then stays on.

This indicates a fault with the system. Consult an Approved Dealer.

tip

The sudden loss of pressure in a tyre (burst tyre, etc.) cannot be detected by the system.

Warning messages

The table below shows possible warning messages related to the tyre pressure resetting procedure.

Steps

Warning messages

Reason

-

Inflate tyre

and

SETTPW

The message is shown while driving. To reset the pressure of all four tyres, stop the vehicle.

1

Tyre pressure

Next OK

to Reset pressure

To reset the pressure of all four tyres, with the vehicle stationary, go to the Tyre pressure screen on the instrument panel, press OK and confirm the reset by selecting the Reset option. Wait until the process is complete.

2

SETTPW launched

The TPW symbol will disappear and the "SETTPW launched" message will be displayed while the readjustment process is in progress. When the message disappears, the process is complete.

3

Tyre pressure

Next OK

to Reset pressure

The resetting procedure has been completed successfully. You can now drive.

Adjusting the tyre pressure

The tyre pressures should be adjusted when cold (please refer to the label located on the corner of the driver’s door).

If tyre pressures cannot be checked when the tyres are cold, the recommended pressures should be increased by 0.2 to 0.3 bar (3 psi).

Never deflate a hot tyre.

Every time a tyre is inflated or the pressure is adjusted, the tyre pressure reference value should be reset.

Replacing wheels/tyres

Only use equipment approved by the dealer network, otherwise there is a risk of the system activating late or not operating correctly Tyres.

After each wheel/tyre replacement operation, adjust the tyre pressure and reset the tyre pressure reference value.

Spare wheel

If the vehicle is equipped, adjust the tyre pressure and reset the tyre pressure reference value.

Tyre pressure faults

The table lists the warning messages that are displayed on the instrument panel A when the system detects a faulty with the tyre pressure.

Warning messages on the instrument panel

The information on the instrument panel signals any possible anomalies in tyre pressure (e.g. flat or punctured tyre).The warning light 1_ALL_040_1_pictogramme.png indicates that, for your own safety, you should stop the vehicle as soon as traffic conditions allow.

Warning light

Warning messages

Reason

2_ALL_197_1_pictogramme.png always on

Inflate tyre and

SETTPW

This indicates that the tyre is not full enough or that a puncture has been detected. Check and adjust the pressure of all four tyres when cold, and restart the system.

2_ALL_197_1_pictogramme.png flashes then remains lit

Adjust Tyre Pressure

and SETTPW

This indicates that the resetting was not successful. Check and readjust the tyre pressure before starting the resetting procedure.

2_ALL_197_1_pictogramme.png flashes and then stays on, accompanied by the 1_ALL_036_1_pictogramme.png warning light

Check TPW

This indicates a system failure. Consult an Approved Dealer.

2_ALL_197_1_pictogramme.png flashes then remains lit

TPW not available

This indicates that an emergency spare wheel different in size from the other four wheels has been fitted on the vehicle. The system remains unavailable until a wheel of the same size as the other wheels is has been fitted and the resetting procedure has been carried out.