Renault Kwid

warning

Activate the hazard warning lights.

Park the vehicle away from traffic on a flat, solid surface where it will not slip (if necessary, place a solid support underneath the base of the jack).

Apply the parking brake and engage a gear (first or reverse gear).

Ask all occupants to exit the vehicle and keep them away from traffic.

Remove the wheel

Use the wheelbrace 1 to loosen the wheel bolts, holding the wheelbrace firmly and using force to unscrew the bolts.

Remove one of the wheel bolts completely and replace it with the auxiliary mounting pin A (supplied with the spare wheel support bolt). The auxiliary mounting pin helps to hold the wheel in place when removing/replacing the wheel bolts.

warning

To prevent any risk of accidents or damage to the vehicle, only crank the jack until the wheel you are replacing is a maximum of 3 cm off the ground.

Position the jack 2 underneath the body, aligning it with the jacking point mark 3 nearest to the wheel to be replaced.

Start extending the jack 2 manually to ensure the base is properly positioned. Make sure that the jack is correctly positioned as shown in the figure.

Insert the wheelbrace all the way through the hole in the jack 2 and tighten it until the wheel is raised high enough off the ground.

Completely remove the two remaining bolts and the wheel.

Fitting the wheel

Fit the spare wheel or the repaired wheel, aligning one of the mounting holes with the auxiliary mounting pin A on the hub/disc.

Holding the wheel bolts and hubcap in one hand, fit and secure the hubcap aligned with the pin and position the two wheel bolts in the remaining mounting holes.

tip

The hubcap should not be mounted to the spare wheel.

Ensure the wheel is sufficiently secured so that removing the pin will not release the wheel from the hub/disc.

Remove the pin and replace it with the remaining wheel bolt. Refit the pin on the spare wheel's support bolt, applying light pressure.

Use the wheelbrace to tighten the wheel bolts evenly. Lower the jack using the wheelbrace until it is no longer supporting the vehicle.

Tighten the wheel bolts firmly.

Place the replaced tyre in the spare wheel storage area and secure it using the mounting bolt supplied.

Place the wheelbrace and jack in the bag.

warning

If the vehicle is parked near traffic, you must warn other drivers of your vehicle's presence using a warning triangle or other devices as required by the local legislation in the country you are in.

Replacing wheels/tyres

warning

For your safety and in order to comply with the law: when you need to change a wheel, it is recommended to fit your vehicle with a set of tyres of the same brand, size, type and structure on the same axle.

They must have a load capacity and speed rating equal to or greater to the original tyres, or as recommended by an approved dealer.

Failing to follow these instructions puts your safety at risk and affects whether your vehicle is fit to drive on the roads.

Risk of loss of control of the vehicle.

Spare wheel

This is located in the luggage compartment.

To access:

  • Open the luggage compartment door;
  • Lift the carpet 1;
  • Remove the jack 2;
  • Loosen the spare wheel support bolt 3;
  • Remove the spare wheel 4;
warning

Be careful when removing or storing the spare wheel as it is heavy and may fall.

warning

If the spare wheel has been stored for several years, have it checked by an expert to ensure it is still suitable and can be used without hazard.

Vehicle equipped with a spare wheel smaller than the other four wheels:

  • Never fit more than one spare wheel to the same vehicle.
  • If the punctured wheel is larger than the spare wheel, the height of the ground clearance will be reduced.
  • Replace the spare wheel as soon as possible with a wheel identical to the original one.
  • When the spare wheel is fitted to the vehicle, which must only be temporary, the driving speed must not exceed the speed indicated on the label on the wheel.
  • Fitting a spare wheel may alter the way the vehicle's behaviour. Avoid sudden acceleration or deceleration and reduce your speed when cornering.
  • If you need to use snow chains, fit the emergency spare wheel to the rear axle and check the tyre pressure.